![logitech c270 software logitech c270 software](https://n2.sdlcdn.com/imgs/i/g/v/Logitech-C270-3-MP-Webcam-SDL015670778-2-c4504.jpeg)
Also, there are eyepiece adapters for sale just for this purpose.
![logitech c270 software logitech c270 software](https://logitechg502.com/wp-content/uploads/2021/03/hardware-veb-kamera-logitech-c270-hd-960-001063__126192769m.jpg)
NOTE: Some people have made adapters to slip over the focus tube instead of in the tube like this will. I took it home and test fit it in my ETX90, It slides in perfectly! I didn’t buy the part at the hardware store (about $4), I found one at a thrift store for $.50 It screws apart in several pieces. It has a nice plastic case around the lamp switch. At the hardware store I noticed that the case on a desk lamp repair switch looked like the perfect size. But for Version 2 of this camera, I set out to find something that works better. Or a 35mm Film container (plastic) is almost a perfect fit. You will need a tube the same diameter and about an inch long to be able to slip this into your focus mechanism. Most scopes use 1.25″ eyepieces, but yours may be 2″ or. It adds quite a bit of weight to the camera. Once I was happy, I soldered the new external LED onto the original LED pads.Īt this point, I also removed the camera holder part that is on the back of the camera. I did this to find the polarity and marked the polarity with that little piece of blue tape. I then went through an assortment of LED’s I have in a drawer and found one that I liked and tested it by placing it on the original LED solder pads. To do this, I created a very small hole on the outside case, adjacent to the LED location on the board. This step is not needed, but I did it because I wanted the “recording” light to be visible from outside the telescope. Use care not to melt or de-solder any of the other components around the LED. The smallest point on my iron was about the size of the whole LED. Also the tip of my solder iron was almost too big to fit. NOTE: Removing this LED I needed the help with a magnifying glass to see the very small solder points. I was not comfortable with this, I didn’t want to risk damaging the board or creating a short in the circuit, but the crush method would probably work just as well. Other people have simply crushed the LED with small pliers. In Version 2 of this camera I decided to remove the LED and replace it with one on the outside of the camera. Others use black paint used for plastic models. In Version 1, I simply covered it with black electrical tape, and that worked pretty good. This needs to be removed or covered so that it does not shine green light into your telescope. Step #5: There is a bright green LED right next to the lens. We don’t want any dust or contamination on the image sensor.) For fun at this point you can play with the lens focus, you can make it focus very close, like 1MM and it acts almost like a microscope! Here is what you should see: (note: do not remove the lens yet.
![logitech c270 software logitech c270 software](https://5.imimg.com/data5/ZY/RU/YR/SELLER-3835345/logitech-webcam-500x500.jpg)
Take a look and find what we will be working on. Step #4: This will now allow you to get to the lens and bright led.
![logitech c270 software logitech c270 software](https://tencomputer.com/wp-content/uploads/2020/06/logitech-c270-search.png)
Step #3: Remove the three small screws holding the next plastic cover. It snaps right off with your fingernails. Step #2: Remove the front faceplate from the camera. Tools you need: Small philips head screwdriver, black electrical tape and a 1.25″ tube (about the size of an eyepiece) When I ran across a sale for C270’s for less than $20, I figured I would take what I learned with V1 and make a better version... The C270 Planet Camera V2! So here are the details on C270 V2: I tried to clean it out but still have a few big dots of dust to deal with. A few nights later I noticed the C270 sensor had quite a bit of dust particles showing up in my captures. One night while benchmarking the C270 vs a Microsoft camera, I accidentally dropped the C270 on the ground while switching cameras. I was able to capture some of my best images ever of Mars, Jupiter and Saturn. That said, this was a low risk modification for me. No guarantees that the modification will work on your camera like it did mine. Working with electronics you should use proper safety for ESD and be careful with hot solder irons. ****> Legal type stuff you should know: Modifying these cameras WILL void your warranty, could render the camera and possibly your computer useless if you mess it up.